What Is a Sump Pump?
A sump pump is a pump used to remove water that has accumulated in a water-collecting sump basin, commonly found in the basements of homes. … Sump pumps are used where basement flooding happens regularly and to solve dampness where the water table is above the foundation of a home.
Why a sump pump is important ?
Sump pumps are electrical pumps that are self-activating that help protect your home from moisture intrusion. They are usually installed below basement of crawlspace floor to remove rising groudwater and surface runoff before it has the chance to seep into the home. Accumulated water can cause interior damages and also encourages the growth of mold, mildew and fungus. The sump pump should always be maintained to ensure all components are working reliably. Ideally, your sump pump should be inspected at least once a year. If your pump runs continuously or repeatedly as a result of a high water table or excess drainage, it may require additional examinations throughout the year.
Keep Your Home Dry, and flood free With a Sump Pump
A small submersible AC sump pump with a garden hose connector.
A sump pump is a pump used to remove water that has accumulated in a water-collecting sump basin, commonly found in the basements of homes. The water may enter via the perimeter drains of a basement waterproofing system, funneling into the basin or because of rain or natural ground water, if the basement is below the water table level.
Sump pumps are used where basement flooding happens regularly and to solve dampness where the water table is above the foundation of a home. Sump pumps send water away from a house to any place where it is no longer problematic, such as a municipal storm drain or a dry well.
Pumps may discharge to the sanitary sewer in older installations. Once considered acceptable, this practice may now violate the plumbing code or municipal bylaws, because it can overwhelm the municipal sewage treatment system. Municipalities urge homeowners to disconnect and reroute sump pump discharge away from sanitary sewers. Fines may be imposed for noncompliance. Many homeowners have inherited their sump pump configurations and do not realize that the pump discharges into the sewer.
Usually hardwired into a home’s electrical system, sump pumps may have a battery backup. The home’s pressurized water supply powers some pumps, eliminating the need for electricity at the expense of using potable water, potentially making them more expensive to operate than electrical pumps and creating an additional water disposal problem. Since a sump basin may overflow if not constantly pumped, a backup system is important for cases when the main power is out for prolonged periods of time, as during a severe storm.
There are generally two types of sump pumps—pedestal and submersible. In the case of the pedestal pump, the motor is mounted above the sump—where it is more easily serviced, but is also more conspicuous. The pump impeller is driven by a long, vertical extension shaft and the impeller is in a scroll housing in the base of the pump. The submersible pump, on the other hand, is entirely mounted inside the sump, and is specially sealed to prevent electrical short circuits. There is debate about which variety of sump pump is better. Pedestal sump pumps usually last longer (25 to 30 years) if they are installed properly and kept free of debris. They are less expensive and easier to remove. Submersible pumps will only last 5 to 15 years. They are more expensive to purchase but can take up debris without clogging.
Sump pump systems are also utilized in industrial and commercial applications to control water table-related problems in surface soil. An artesian aquifer or periodic high water table situation can cause the ground to become unstable due to water saturation. As long as the pump functions, the surface soil will remain stable. These sumps are typically ten feet in depth or more; lined with corrugated metal pipe that contains perforations or drain holes throughout. They may include electronic control systems with visual and audible alarms and are usually covered to prevent debris and animals from falling in.
Modern sump pump components in the United States are standardized. They consist of:
- A plastic, metal, or concrete container forming a sump basin, approximately 2 feet (0.6 m) across and 2 to 3 feet (0.6 to 1 m) deep, 15 to 25 U.S. gallons (60 to 100 litre) capacity;
- A sump pump, either 1/3 or 1/2 horsepower (200 or 400 W), either battery or mains powered (or both).
Selection of a sump pump may consider:
- Automatic vs. manual operation – pump may be controlled automatically by a level switch.
- Power – Sump pump motive power will vary from 1/4 horsepower to multiple horsepower.
- Head pressure – The hydraulic head pressure of a sump pump describes the maximum height that the pump will move water. For instance, a sump pump with a 15 feet (4.6 m) maximum head (also called a shutoff head) will raise water up 15 feet (4.6 m) before it completely loses flow.
- Power cord length – Running a more powerful electrical motor a long distance from the main service panel will require heavier gauge wiring to assure sufficient voltage at the motor for proper pump performance.
- Phase and voltage – Sump pumps powered from the AC mains are available with single-phase or three-phase induction motors, rated for 110–120, 220–240, or 460 volts. Three-phase power is typically not available in residential locations.
- Water level sensing switch type – Pressure switches are fully enclosed, usually inside the pump body, making them immune to obstructions or floating debris in the sump basin. Float switches, particularly the types attached to the end of a short length of flexible electrical cable, can get tangled or obstructed, especially if the pump is prone to movement in the basin due to torque effects when starting and stopping. Pressure switches are typically factory set and not adjustable, while float switches can be adjusted in place to set the high and low water levels in the sump basin. There is a solid state switch utilizing field-effect technology, which will turn on and off the pump through use of an internal switch and a piggyback plug.
- Backup system and alarm for critical applications.
A secondary, typically battery-powered sump pump can operate if the first pump fails. A battery-powered secondary pump will have a separate battery and charger system to provide power if normal supply is interrupted.
Alternative sump pump systems can be driven by municipal water pressure. Water-powered ejector pumps have a separate pump, float and check valve. The float controlling a backup pump is mounted in the sump pit above the normal high water mark. Under normal conditions, the main electric powered sump pump will handle all the pumping duties. When water rises higher than normal for any reason, the backup float in the sump is lifted and activates the backup sump pump. An ejector pump can also be connected to a garden hose to supply high-pressure water, with another hose to carry the water away. Although such ejector pumps waste water and are relatively inefficient, they have the advantage of having no moving parts and offer the utmost in reliability.
If the backup sump system is rarely used, a component failure may not be noticed, and the system may fail when needed. Some battery control units test the system periodically and alert on failed electrical components.
A simple, battery-powered water alarm can be hung a short distance below the top of the sump to sound an alarm should the water level rise too high.
Illustration of a typical pedestal-type sump pump.
Sump basins and sump pumps must be maintained. Typical recommendations suggest examining equipment every year. Pumps running frequently due to higher water table, water drainage, or weather conditions should be examined more frequently. Sump pumps, being mechanical devices, will fail eventually, which could lead to a flooded basement and costly repairs. Redundancy in the system (multiple/secondary pumps) can help to avoid problems when maintenance and repairs are needed on the primary system.
When examining a sump pump and cleaning it, dirt, gravel, sand, and other debris should be removed to increase efficiency and extend the life of the pump. These obstructions can also decrease the pump’s ability to drain the sump, and can allow the sump to overflow. The check valve can also jam from the debris. Examine the discharge line opening, when applicable, to ensure there are no obstructions in the line. Even a partially obstructed discharge line can force a sump pump to work harder and increase its chance of overheating and failure.
Float switches are used to automatically turn the sump pump on when water rises to a preset level. Float switches must be clear of any obstructions within the sump. A float guard can be used to prevent the float switch from accidentally resting on the pump housing, and remaining on. As mechanical float switches can wear out, they should be periodically tested by actuating them manually to assure that they continue to move freely and that the switch contacts are opening and closing properly.
If left in standing water, pedestal pumps should be manually run from time to time, even if the water in the sump isn’t high enough to trip the float switch. This is because these pumps are incapable of removing all the water in a sump and the lower bearing or bushing for the pump impeller shaft tends to remain submerged, making it prone to corrosion and eventually freezing the drive shaft in the bearing. In the alternative, a pedestal pump that is expected to remain idle for an extended time should be removed from the sump and stored out of water, or the sump should be mopped out to bring the level of the remaining water well below the lower shaft bearing.
Testing Your Sump Pump
- In damp areas, GFCI breakers may trip, effectively shutting off the sump pump. Check in on your sump pump periodically so you can reset the GFCI if necessary.
- Remove the plastic cover, it may be screwed down and you will need to remove the screws to get access to the pump and components.
- Ensure the (pump) mechanism is standing upright. While operating vibrations may cause it to fall over or flip onto it’s side. In this position the float arm will jam up so it can’t activate the pump to drain the water out.
- A simple test is to periodically pour a bucket of water into the pit to make sure the pump starts automatically and the water drains quickly once the pump is on. If the pump doesn’t start, have it serviced.
- Physically pull up the submersible pump from the pit and clean the grate on the bottom. The sucking action of the pump can pull small stones into the grate, blocking the inlet or damaging the pump over time.